Product - Clamps and Accessories | KOTO SANGYO CO., LTD.|

Clamps and Accessories

MINI CLAMP

C-80

This is designed so as not to occur slide when pulling.

The average pulling capacity: 15,000N.

mini clamp / image2

NARROW MINI CLAMP

C-70C (PAT.P)

Max 15,000N pulling capacity.

With a chain shackle in order to use 2 clamps at the same time.

Usable for hexagonal front side member(TOYOTA - Vitz, bB, Fun cargo, Spacio, New Corolla and New HONDA Vehicles).

narrow mini clamp / image2

OFFSET CLAMP

C-90N

Suitable for pulling of monocoque body as this model can be pulled in all directions at the same time.

Convenient to pull the protuberance of flange and frame.

Removable a side ring.

offset clamp / image2

OFFSET RIPURU CLAMP

C-90NT

Can exchange the edge.

Suitable for pulling work of monocoque body.

Pulling capacity: 19,600N. (according to our experimental data)

offset ripuru clamp / image2

OFFSET CLAMP

C-101

44mm Grab wide is the most suitable for pulling of side frames.

Correspond to side member.

Pulling capacity: 7,000N.

OFFSET CLAMP

C-102

Grab 48mm wide is suitable for pulling of side frames.

Correspond to side members.

Pulling capacity: 5,000N.

OFFSET CLAMP

C-103

45mm grab wide with 73mm inside wide is convenient for pulling of flanges and frames.

CAM STOPPER WRENCH

CL-400

Can be extracted easily at an awkward place.

This tool is very efficient in pulling job because it can be utilized the screw holes and the fixture holes on body.

cam stopper wrench / image2

CHAIN HOOK

CH-10

Any chain makes a quick change the chain with hook if you only put the pin into the ring of your chain.

JOINT HOOK

HL-16N

Can be used widely as chain joint or Joint for a chain and a hook.

joint hook / image2

JIG PLATE HOOK

HL-18

This is for welding washer hook for body sheet pulling.

Lightweight and strong as this body is used aluminum alloy, which is hard to turn on the electricity.

jig plate hook / image2

RING JOINT

HL-10

Can be adjusted the long chain to short chain.

Can make a long chain by connecting some short chains.

ring joint / image2

TURN BUCKLE

T-12

Can be rid the slack of chain because of 140mm elastic model.

turn buckle / image2

SAFETY WIRE

SF-150

Please use it for safety when stretching a chain between a car body and a clamp in order to escape injury during clamp pulling work.

This model functions its dangerous prevention stopper when clamp came off.

safety wire / image2

SLIDE HAMMER & SHAFT

BL / KP / BP

You can choose freely about the combination of slide hammer and shaft.

This “T” shaped handle is designed not to be pinched finger due to hammer shock.

slide hammer & shaft (hige-power type) / image1

SLIDE HAMMER & SHAFT (High-Power type)

The hand guard (handle part ) of slide shaft is designed not to be pinched finger due to hammer shock.

BODY HOOK OPTIONAL PARTS

BPS

This is a body hook set for the slide hammers and handle shafts of 9/16” screw dia.

more imformation

BODY HOOK OPTIONAL PARTS

HPS

This is a body hook set for the slide hammers and handle shafts of HP (High-Power) type.

more imformation

POWER CHAIN

08－50～C10－50

No.08 is for 8-ton use and No.10 is for 10-ton use.

Length available from 0.5m to 5m at 0.5m intervals.

As for the details of model PO06－20 and PO06－30, please see our pulling tower section.

8ton			10ton
Model No.	Length	Weight	Model No.	Length	Weight
08-05	0.5m	0.98	10-05	0.5m	1.34
08-10	1.0m	1.96	10-10	1.0m	2.67
08-15	1.5m	2.94	10-15	1.5m	4.02
08-20	2.05m	3.92	10-20	2.05m	5.36
08-25	2.5m	4.90	10-25	2.5m	6.70
08-30	3.0m	5.88	10-30	3.0m	8.04
08-35	3.5m	6.86	10-35	3.5m	9.38
08-40	4.0m	7.84	10-40	4.0m	10.72
08-45	4.5m	8.82	10-45	4.5m	12.06
08-50	5.0m	9.80	10-50	5.0m	13.40

more imformation

VICE SERIES

KC-190 (PAT)

Vice series

more imformation

WHEEL CHISEL

WT-220

Suitable for the peeling fall work of the rear fender’s sealer.

Exfoliation work for spot sections at narrow place.

wheel chisel / image2

ATTACHMENT HAMMER

AMH-900

Can be used 9 kings of hammer head if exchanging its head.

The hammer head (milled part) is used stainless so as not to cling hammer’s rust on the steel plate.

DULLY BLOCK SET

KDB-200

High tensile strength steel plate.

Aluminum alloy steel plate venturi dolly.

Using a stainless steel so as not to come in the rust.

The most suitable for a fender panel and a quarter panel.

Page top